How’s your water pump doing?  Short video to help you see if it’s in trouble.

Do you appreciate your water pump?

Leaking antifreeze?  It could be your water pump.

This car gives new meaning to the term water pump.  See this short video to learn more about the water pump in your car.

What do you know about your water pump?  Watch this short video – because knowing is half the battle.

Watch this video to learn the warning signs of a failing water pump.

What do you need to know about your water pump.  Watch this short video.

Today we’re going to be talking about serpentine belts. Let’s start by talking about the accessories that are driven by the serpentine belt. First is the alternator. That’s the device that makes electricity to power the vehicle and recharge the battery. Then there’s the air conditioning compressor that makes cool air for you.

The power steering and power brake pumps are driven by the serpentine belt in most vehicles. Those pumps make the pressure that assists your steering and braking.

In many vehicles, the water pump is driven by the serpentine belt. The water pump is what circulates the coolant that protects your engine. In some cars, the water pump is driven by the timing belt.

The radiator cooling fans on some vehicles are also driven by the serpentine belt. Some have separate electric motors. That’s really a lot of work for one belt.

But modern engine design has a single belt that snakes around the front of the engine and drives most if not all of these accessories. Serpentine belts do a lot of work, but they’re tough and can last for thousands of miles.

Just how long will they last? That’ll vary for each individual car. Your manufacturer will have a recommendation for when it should be changed, but it could need it sooner. The good news is that a visual inspection can reveal a belt that’s getting close to failing.

Your service center can look at the belt: if it has more than three or four cracks per inch it needs to be replaced. A deep crack that’s more than half the depth of the belt – replace. Frayed, missing pieces, a shiny glazed look? It’s out of there.

What’s involved in replacing the belt? First the old belt is removed. Then a new one is fitted around all the pulleys for the accessories and the drive. There’s a special pulley called a tensioner.

This pulley is mounted to the engine block with a spring loaded arm. Its job is to apply the correct amount of tension to the belt to keep it from getting loose and maybe slipping off. Because the spring in the tensioner pulley wears out, AutoNetTV recommends replacing them at the same time as the belt. It just makes sense.

What are the warning signs that there’s a problem with the serpentine belt? You may hear a squealing sound from under the hood when accelerating. A loose belt might give you a slow, slapping sound.

What do you do if your belt breaks? If you’ve actually had that happen on the freeway, it can be a little scary. Often the first thing you notice is that you have no power steering or power brakes. Don’t panic – you can still steer and brake, but you’ll have to do the work. It’ll be harder to steer and you’ll need more time and effort to stop, so plan accordingly.

Your dashboard will light up will all kinds of warnings. You’ll see a warning about your cooling system if you have a water pump that’s driven by the serpentine belt. This is very critical because without your cooling system working, your engine will overheat. If you don’t stop you’ll have massive engine damage, maybe to the point that you need a new engine. Pull over as quickly as you safely can. Open your windows and turn the heater on full blast to provide a little engine cooling and pulled over as soon as possible.

The battery light will come on because the alternator isn’t working. If your car’s water pump isn’t driven by the serpentine belt, you’re not in danger of overheating so you can drive a little further if necessary. But the battery will run down to the point where the car won’t run and will just shut off. You don’t want that to happen while you’re driving.

Remember, this does not have to happen if you replace your serpentine belt on schedule. Ask your technician to check your belts and hoses from time to time so you can take care of them if they need to be replaced prematurely.

Today we want to talk about a very important system in our cars – the cooling system. It’s one of those things that you don’t give much thought to until it fails and then you’re stranded by the side of the road.

Cooling systems fail more often than any other mechanical system – usually because of neglect. Don’t you hate it when something breaks, and you could have done something to prevent it?

The good news is that if you take care of your cooling system it can keep working for the life of your car

Here at AutoNetTV, we emphasize preventive maintenance services like replacing your coolant according to the factory schedule. But the various parts that make up the cooling system need attention too. The major components of the cooling system are the water pump, freeze plugs, the thermostat, the radiator, cooling fans, the heater core, the pressure cap, the overflow tank and the hoses.

It sounds complicated, but we don’t have to be experts – we can leave that to our service technicians. But, having an overview will help us remember to take care of our cooling systems.

Most people would be surprised to know that burning fuel in your engine produces up to 4,500 degrees of heat. And all that heat has to be dealt with. If the heat can’t be drawn off the engine, the pistons will literally weld themselves to the inside of the cylinders – then you just have to throw the engine away and get a new one. That would cost thousands of dollars.

Now the water pump is what forces the coolant through passages in the engine to absorb heat. The pump is driven by a belt that needs replacement from time to time. And the water pump will eventually wear out and need to be replaced. Spending some money on replacing the belts and water pump is much less than the cost of repairing the massive damage that can be done when an engine seizes.

There’s another little part of the coolant system that protects the engine. It’s called a freeze plug. If you remember from high school chemistry, water expands when it freezes. In very cold areas, the coolant can actually freeze when the vehicle is left sitting.

It is hard to believe, but the expanding frozen coolant can actually crack the engine block. The freeze plugs fit into the engine block. They fit tight enough to withstand the pressure of a running engine, but can expand or pop out if the coolant freezes. These little things save a lot of engine blocks.

That brings up a good point. An engine has to work in all kinds of temperatures – extremely hot as well as very cold. How does the cooling system adapt to external temperatures as well as varying operating conditions?

Well, it’s much like the way you keep your house at a comfortable temperature all year round – with a thermostat. The thermostat in your car controls how much coolant flows through your engine. When the engine is cold, it restricts coolant flow until the engine comes up to an efficient operating temperature. Then it starts opening up to move more coolant to keep the temperature within a specified range.

The thermostat needs to be replaced from time to time as well. It’s easy to diagnose a failed thermostat and is fairly inexpensive to replace.

Now we’ve been talking about all this heat we’ve got to get rid of, but haven’t really talked about where it goes. That’s where the radiator comes in. The hot coolant passes through the radiator. Air flows past the cooling fins and cools the coolant.

The radiator has two tanks that hold coolant: sometimes one the top and bottom or one on either side. If you have an automatic transmission, one of the tanks will also contain a second tank that cools the transmission fluid. Large SUV’s and trucks often have a separate transmission cooler.

So when you drive, the air is forced past the radiator. But driving doesn’t produce enough air flow. So the radiator has cooling fans that force fresh air over the radiator. These fans may be powered by a belt or by electric motors.

Now, you also have something called a heater core. The heater core is like a mini radiator. A small fan blows air over the heater core and into the passenger compartment of your vehicle. That’s how you warm your car when it’s cold out.

Next is the radiator cap. With most newer cars, you never remove the radiator cap, except to replace it. You add coolant through the overflow tank. The radiator cap is also called a pressure cap, because its job is to maintain pressure in the cooling system.

High pressure raises the boiling point of the coolant, so it cools more effectively even in very demanding conditions. That is why you need to replace the cap from time to time. They recommend changing it out every time you replace your coolant.

Coming back to the overflow tank, it is needed because when the coolant gets hot it expands and the overflow holds the extra volume. The tank helps maintain the proper level of coolant and keeps air out of the system. You should never open the radiator cap or over flow tank when the engine is hot. This could lead to serious burns.

What else do we need to do to keep our cooling systems working well? Well, there are the hoses that hook all of these pieces together. They’re obviously very tough to deal with the pressure and high temperatures. But they do get worn. Sometimes they get spongy from the heat.

Sometimes they lose their connection to the radiator, water pump, etc. It’s a great idea to have your service center inspect your hoses at least once a year and replace them, if needed, before they break.

Your cooling system is very important.  It circulates coolant through the radiator and your engine to protect your car from overheating. There are five main components to the cooling system: the radiator, the radiator cap, the hoses, the thermostat and the water pump.

The water pump’s like the heart of your cooling system, circulating the fluid throughout.  It’s a small pump that’s driven by the engine: usually by belt, but sometimes by a chain or gear.

The water pump only operates when the engine’s running. Water pump failure is pretty routine.  Some start failing at around 40,000 miles, but most fail by 100,000 miles.  Consult your owners’ manual or service technician to see what’s recommended.

Since a water pump either works or it doesn’t, you need to change it when it fails. Water pumps fail in one of two ways: the bearings fail or they begin to leak.  It’s possible to have a leak from a cracked water pump, but it usually leaks at the gasket where it attaches to the engine.

So how can you tell when the water pump is failing? If you can hear a low-pitched grinding sound coming from the water pump – it’s got a problem.  If you can see coolant in that area, you’ve got a leak.

Some water pumps are driven off the timing belt.  They might be under a plastic cover so you can’t see the water pump.  Look for coolant on the driveway.  If you see some, have your service center check it out.

Most timing belts need to be changed at 60,000 miles – some longer.  It’s a good idea to change your water pump at the same time if it’s one of those that’s driven off the timing belt.  To start with, 90% of the work’s already done with the timing belt change. And, if you don’t, and develop a leak later, you’ll have to change the belt again along with the water pump because the belt will have been contaminated by the leaking coolant.

You can replace your water pump with a brand spankin’ new one or with a rebuilt pump.  Rebuilt will save you some money, but ask your technician what he thinks. Don’t feel too bad if your water pump gives out.  They will all wear out eventually.  Your service technician can get you back on the road and on with your life.